Install paclink-unix

home
Install AX.25
Install paclink-unix
Configure a single MTA
- Configure postfix
- Configure exim
Configure Winlink Secure Login

Test, Verify & Debug paclink-unix

paclink-unix Use Cases

use_cases

paclink-unix email clients

Configure email clients

Brief Comparison of TNCs

Compare 1200 baud TNCs

About

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

--- plu:example_config_files:systemd [2018/11/23 12:31]
gunn created
+++ plu:example_config_files:systemd [2018/11/23 15:55] (current)
gunn
@@ Line 3: / Line 3: @@
 ===== systemd files in /etc/systemd/system =====
+  * Up-to-date files can be found in nwdigitalradio/n7nix repo [[https://github.com/nwdigitalradio/n7nix/tree/master/systemd/sysd | here]]
 === ax25dev.service ===
 <file>
@@ Line 10: / Line 11: @@
 Requires=direwolf.service
 After=direwolf.service
-#After=network-online.target
 [Service]
@@ Line 84: / Line 84: @@
 WantedBy=multi-user.target
 DefaultInstance=1
+</file>
+===== Files in /etc =====
+  * Up-to-date files can be found in nwdigitalradio/n7nix repo [[https://github.com/nwdigitalradio/n7nix/tree/master/systemd/sysd | here]]
+=== direwolf.conf ===
+<file>
+#############################################################
+#                                                           #
+#               Configuration file for Dire Wolf            #
+#                                                           #
+#                   Linux version                           #
+#                                                           #
+#############################################################
+#
+# Consult the User Guide for more details on configuration options.
+#############################################################
+#                                                           #
+#               FIRST AUDIO DEVICE PROPERTIES               #
+#               (Channel 0 + 1 if in stereo)                #
+#                                                           #
+#############################################################
+ADEVICE plughw:CARD=udrc,DEV=0 plughw:CARD=udrc,DEV=0
+ACHANNELS 2
+#############################################################
+#                                                           #
+#               CHANNEL 0 PROPERTIES                        #
+#                                                           #
+#############################################################
+CHANNEL 0
+PTT GPIO 12
+MODEM 1200
+MYCALL N7NIX-1
+#############################################################
+#                                                           #
+#               CHANNEL 1 PROPERTIES                        #
+#                                                           #
+#############################################################
+CHANNEL 1
+PTT GPIO 23
+MODEM 1200
+MYCALL N7NIX-2
+#############################################################
+#                                                           #
+#               VIRTUAL TNC SERVER PROPERTIES               #
+#                                                           #
+#############################################################
+AGWPORT 8000
+KISSPORT 8001
+</file>
+===== Files in /etc/ax25 =====
+  * Up-to-date files can be found in nwdigitalradio/n7nix repo [[https://github.com/nwdigitalradio/n7nix/tree/master/systemd/ax25 | here]]
+=== ax25dev-parms ===
+<file>
+#!/bin/bash
+if [[ $# -gt 0 ]] ; then
+   Device=$1
+else
+   awk '/device/ { print $7 }' /tmp/ax25-config.tmp > /tmp/ax25-config-tmp
+   read Device < /tmp/ax25-config-tmp
+   if [[ -z "$Device" ]] ; then
+      Device="ax0"
+      echo "Set Device to default: $Device"
+   fi
+fi
+echo "Using Device = $Device"
+if [ -d /proc/sys/net/ax25/$Device ] ; then
+ PARMDIR="/proc/sys/net/ax25/$Device"
+# Parms for a USER Port
+echo 3000    > $PARMDIR/t1_timeout		# (Frack) /1000 = ? Sec
+echo 1000    > $PARMDIR/t2_timeout 		# (RESPtime) /1000 = ? sec
+echo 300000  > $PARMDIR/t3_timeout 		# (Check) /6000 = ? Min
+echo 900000  > $PARMDIR/idle_timeout		# Idle Timer /6000 = ? min
+echo 2       > $PARMDIR/standard_window_size	# Outstanding Frames
+echo 12      > $PARMDIR/maximum_retry_count	# Max Retrys
+echo 256     > $PARMDIR/maximum_packet_length	# Paclen
+echo 0       > $PARMDIR/ax25_default_mode
+echo 0       > $PARMDIR/ip_default_mode
+echo 0       > $PARMDIR/backoff_type
+echo 2       > $PARMDIR/connect_mode
+#echo 180000 > $PARMDIR/dama_slave_timeout
+echo 32      > $PARMDIR/extended_window_size
+echo 0       > $PARMDIR/protocol
+        ifconfig $Device netmask 255.255.255.255
+        echo " Port ${PORTNAME} attached to ${Device} "
+else
+        echo "** Error setting Device: $Device parms**"
+fi
+echo "ax25dev-parms finished"
+exit 0
+</file>
+=== ax25-upd ===
+<file>
+#!/bin/bash
+#
+# ax25-upd for use with systemd & direwolf
+# Ax25, rose, & mkiss - are pre-loaded via /etc/modules or built into kernel
+#
+# Uncomment this statement for debug echos
+DEBUG=1
+SBINDIR=/usr/local/sbin
+BINDIR=/usr/local/bin
+UDRCII=false
+# portname set in /etc/ax25/axports
+PORTNAME_1="udr0"
+PORTNAME_2="udr1"
+SERIALPORT_DIREWOLF="/tmp/kisstnc"
+firmware_prodfile="/sys/firmware/devicetree/base/hat/product"
+firmware_prod_idfile="/sys/firmware/devicetree/base/hat/product_id"
+firmware_vendorfile="/sys/firmware/devicetree/base/hat/vendor"
+PROD_ID_NAMES=("INVALID" "INVALID" "UDRC" "UDRC II" "DRAWS" "1WSpot")
+NWDIG_VENDOR_NAME="NW Digital Radio"
+function dbgecho { if [ ! -z "$DEBUG" ] ; then echo "$*"; fi }
+# ===== function EEPROM id_check
+# Return code:
+# 0 = no EEPROM or no device tree found
+# 1 = HAT found but not a UDRC
+# 2 = UDRC
+# 3 = UDRC II
+# 4 = DRAWS
+# 5 = 1WSpot
+function id_check() {
+# Initialize to EEPROM not found
+udrc_prod_id=0
+# Does firmware file exist
+if [ -f $firmware_prodfile ] ; then
+   # Read product file
+   UDRC_PROD="$(tr -d '\0' < $firmware_prodfile)"
+   # Read vendor file
+   FIRM_VENDOR="$(tr -d '\0' < $firmware_vendorfile)"
+   # Read product id file
+   UDRC_ID="$(tr -d '\0' < $firmware_prod_idfile)"
+   #get last character in product id file
+   UDRC_ID=${UDRC_ID: -1}
+   dbgecho "UDRC_PROD: $UDRC_PROD, ID: $UDRC_ID"
+   if [[ "$FIRM_VENDOR" == "$NWDIG_VENDOR_NAME" ]] ; then
+      case $UDRC_PROD in
+         "Universal Digital Radio Controller")
+            udrc_prod_id=2
+         ;;
+         "Universal Digital Radio Controller II")
+            udrc_prod_id=3
+         ;;
+         "Digital Radio Amateur Work Station")
+            udrc_prod_id=4
+         ;;
+         "1WSpot")
+            udrc_prod_id=5
+         ;;
+         *)
+            echo "Found something but not a UDRC: $UDRC_PROD"
+            udrc_prod_id=1
+         ;;
+      esac
+   else
+      dbgecho "Probably not a NW Digital Radio product: $FIRM_VENDOR"
+      udrc_prod_id=1
+   fi
+   if [ udrc_prod_id != 0 ] && [ udrc_prod_id != 1 ] ; then
+      if (( UDRC_ID == udrc_prod_id )) ; then
+         dbgecho "Product ID match: $udrc_prod_id"
+      else
+         echo "Product ID MISMATCH $UDRC_ID : $udrc_prod_id"
+         udrc_prod_id=1
+      fi
+   fi
+   dbgecho "Found HAT for ${PROD_ID_NAMES[$UDRC_ID]} with product ID: $UDRC_ID"
+else
+   # RPi HAT ID EEPROM may not have been programmed in engineering samples
+   # or there is no RPi HAT installed.
+   udrc_prod_id=0
+fi
+return $udrc_prod_id
+}
+# ===== main =====
+echo "ax25-upd: Start Port ${PORTNAME_1} with device ${SERIALPORT_DIREWOLF}"
+if [ -L $SERIALPORT_DIREWOLF ] ; then
+    echo "Direwolf serial port ready"
+else
+    echo "Direwolf serial port NOT FOUND"
+d    exit 1
+fi
+# Check which UDRC product is found
+id_check
+id_check_ret="$?"
+# Initialize kissattach return code
+kissattach_ret=-1
+case $id_check_ret in
+|1)
+   echo "No UDRC found, exiting"
+   exit 1
+;;
+)
+   echo "Original UDRC is installed."
+# use port 1 with mkiss
+   pseudoterm=$($SBINDIR/mkiss $SERIALPORT_DIREWOLF /dev/ptmx none | tail -1)
+   echo "using mkiss with UDRC and pseudo term=$pseudoterm on port 1"
+   $SBINDIR/kissattach  ${pseudoterm} ${PORTNAME_1} 44.24.197.66 >/tmp/ax25-config.tmp
+   kissattach_ret=$?
+   dbgecho "kissattach return: $?"
+   /etc/ax25/ax25dev-parms ax0
+;;
+|4)
+   echo "UDRC II or DRAWS installed"
+# use port 2 with mkiss
+   pseudoterm=$($SBINDIR/mkiss $SERIALPORT_DIREWOLF /dev/ptmx /dev/ptmx | tail -1)
+   echo "$pseudoterm" > /tmp/ax25-config.tmp
+   pseudoterm_1=$(echo $pseudoterm | cut -d ' ' -f1)
+   pseudoterm_2=$(echo $pseudoterm | cut -d ' ' -f2)
+   echo "using mkiss with UDRC II and pseudo term_1: $pseudoterm_1 pseudo term_2: $pseudoterm_2"
+   $SBINDIR/kissattach  ${pseudoterm_1} ${PORTNAME_1} 44.24.197.66 >/tmp/ax25-config_1.tmp
+   $SBINDIR/kissattach  ${pseudoterm_2} ${PORTNAME_2} 44.24.197.67 >/tmp/ax25-config_2.tmp
+   kissattach_ret=$?
+   dbgecho "kissattach return: $?"
+   /etc/ax25/ax25dev-parms ax0
+   /etc/ax25/ax25dev-parms ax1
+   echo " Port ${PORTNAME_1} attached to ax0"
+   echo " Port ${PORTNAME_2} attached to ax1"
+;;
+)
+   echo "One Watt Spot installed"
+# use port 1 with mkiss
+   pseudoterm=$($SBINDIR/mkiss $SERIALPORT_DIREWOLF /dev/ptmx none | tail -1)
+   echo "using mkiss with UDRC and pseudo term=$pseudoterm on port 1"
+   $SBINDIR/kissattach  ${pseudoterm} ${PORTNAME_1} 44.24.197.66 >/tmp/ax25-config.tmp
+   kissattach_ret=$?
+   dbgecho "kissattach return: $?"
+   /etc/ax25/ax25dev-parms ax0
+;;
+*)
+   echo "Invalid udrc id ... exiting"
+   exit 1
+;;
+esac
+# configure netrom
+# Needs a callsign
+# source /home/pi/n7nix/systemd/ax25/nr-up.sh
+# AX25-upd (End)
+echo
+echo "ax25-upd script finished"
+exit 0
+</file>
+=== ax25-downd ===
+<file>
+#!/bin/bash
+#
+SBINPATH="/usr/local/sbin"
+echo "ax25-downd start"
+# Stop FPAC
+#    /usr/local/sbin/myfpac.sh stop
+# Stop Ax25 support
+#  for PROC_NAME in beacon ax25d ax25ipd ax25rtd mheardd listen saxIgate
+  for PROC_NAME in beacon ax25d ax25ipd ax25rtd mheardd saxIgate
+    do
+      PID=`/bin/pidof -x $PROC_NAME`
+      if [ -n "$PID" ]; then
+         kill -TERM $PID > /dev/null
+         echo "$PROC_NAME - $PID "
+         sleep 1
+      fi
+    done
+# If netromd is running
+  pidof netromd > /dev/null
+  if [ $? -eq 0 ]; then
+# Save NetRom routes
+   $SBINPATH/nodesave -p $SBINPATH /var/ax25/nrsave && echo "N/R routes saved"
+# Stop NetRom
+    killall netromd > /dev/null
+    echo "Netrom Stopped"
+  else
+    echo "Netrom daemon not running"
+  fi
+# Close sockets
+echo "Detach Ax/Nr/Sp Devices"
+ifconfig|grep AMPR > /tmp/ax25-config.tmp
+i=0
+iface=$(awk ' NR == '1' { print $1 }' /tmp/ax25-config.tmp)
+while [ "$iface" != "" ] ; do
+   let i=i+1
+   iface=$(awk ' NR == '$i' { print $1 }' /tmp/ax25-config.tmp)
+   if [ "$iface" != "" ] && [ "${iface:0:2}" == "nr" ] ; then
+#      echo "select: $iface, iface: ${iface:0:2}"
+      ifconfig "$iface" down
+      echo " $iface down"
+  fi
+done
+# Stop Kissattach
+killall -KILL kissattach > /dev/null
+# Empty Heard List
+#cat /dev/null > /var/ax25/mheard/mheard.dat
+# End of ax25-down
+echo "ax25-downd finished"
+exit 0
+</file>
+=== axports ===
+<file>
+# /usr/local/etc/ax25/axports
+#
+# Use simple descriptive names for the ports, to make debugging
+# other associated software easier.
+#
+# The format of this file is:
+#portname	callsign	speed	paclen	window	description
+udr0            N7NIX-10        9600    255     2       Winlink
+</file>
+=== ax25d.conf ===
+<file>
+# /usr/local/etc/ax25/ax25d.conf
+#
+# ax25d Configuration File.
+#
+#
+[N7NIX-10 VIA udr0]
+NOCALL   * * * * * *  L
+NOCALL   * * * * * *  L
+default  * * * * * *  -	rmsgw /usr/local/bin/rmsgw rmsgw -l debug -P %d %U
+#
+[N7NIX VIA udr0]
+NOCALL   * * * * * *  L
+default  * * * * * *  0  gunn  /usr/local/bin/wl2kax25d wl2kax25d -c %U -a %d
+#
 </file>

plu/example_config_files/systemd.1543005094.txt.gz · Last modified: 2018/11/23 12:31 by gunn

Show page Old revisions

Media Manager Back to top