Install paclink-unix
- Configure a single MTA
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
plu:example_config_files:systemd [2018/11/23 12:59] gunn [Files in /etc/ax25] |
plu:example_config_files:systemd [2018/11/23 15:55] (current) gunn |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ===== systemd files in /etc/systemd/system ===== | ===== systemd files in /etc/systemd/system ===== | ||
| + | * Up-to-date files can be found in nwdigitalradio/n7nix repo [[https://github.com/nwdigitalradio/n7nix/tree/master/systemd/sysd | here]] | ||
| === ax25dev.service === | === ax25dev.service === | ||
| <file> | <file> | ||
| Line 85: | Line 86: | ||
| </file> | </file> | ||
| ===== Files in /etc ===== | ===== Files in /etc ===== | ||
| + | * Up-to-date files can be found in nwdigitalradio/n7nix repo [[https://github.com/nwdigitalradio/n7nix/tree/master/systemd/sysd | here]] | ||
| === direwolf.conf === | === direwolf.conf === | ||
| <file> | <file> | ||
| Line 127: | Line 129: | ||
| CHANNEL 1 | CHANNEL 1 | ||
| - | PTT GPIO 12 | + | PTT GPIO 23 |
| MODEM 1200 | MODEM 1200 | ||
| MYCALL N7NIX-2 | MYCALL N7NIX-2 | ||
| Line 141: | Line 143: | ||
| </file> | </file> | ||
| ===== Files in /etc/ax25 ===== | ===== Files in /etc/ax25 ===== | ||
| + | * Up-to-date files can be found in nwdigitalradio/n7nix repo [[https://github.com/nwdigitalradio/n7nix/tree/master/systemd/ax25 | here]] | ||
| + | |||
| === ax25dev-parms === | === ax25dev-parms === | ||
| <file> | <file> | ||
| Line 208: | Line 212: | ||
| firmware_vendorfile="/sys/firmware/devicetree/base/hat/vendor" | firmware_vendorfile="/sys/firmware/devicetree/base/hat/vendor" | ||
| - | PROD_ID_NAMES=("INVALID" "INVALID" "UDRC" "UDRC II" "1WSpot") | + | PROD_ID_NAMES=("INVALID" "INVALID" "UDRC" "UDRC II" "DRAWS" "1WSpot") |
| NWDIG_VENDOR_NAME="NW Digital Radio" | NWDIG_VENDOR_NAME="NW Digital Radio" | ||
| Line 316: | Line 320: | ||
| /etc/ax25/ax25dev-parms ax0 | /etc/ax25/ax25dev-parms ax0 | ||
| ;; | ;; | ||
| - | 3) | + | 3|4) |
| - | echo "UDRC II installed" | + | echo "UDRC II or DRAWS installed" |
| # use port 2 with mkiss | # use port 2 with mkiss | ||
| pseudoterm=$($SBINDIR/mkiss $SERIALPORT_DIREWOLF /dev/ptmx /dev/ptmx | tail -1) | pseudoterm=$($SBINDIR/mkiss $SERIALPORT_DIREWOLF /dev/ptmx /dev/ptmx | tail -1) | ||
| Line 333: | Line 337: | ||
| echo " Port ${PORTNAME_2} attached to ax1" | echo " Port ${PORTNAME_2} attached to ax1" | ||
| ;; | ;; | ||
| - | 4) | + | 5) |
| echo "One Watt Spot installed" | echo "One Watt Spot installed" | ||
| # use port 1 with mkiss | # use port 1 with mkiss | ||
| Line 420: | Line 424: | ||
| echo "ax25-downd finished" | echo "ax25-downd finished" | ||
| exit 0 | exit 0 | ||
| + | </file> | ||
| + | === axports === | ||
| + | <file> | ||
| + | # /usr/local/etc/ax25/axports | ||
| + | # | ||
| + | # Use simple descriptive names for the ports, to make debugging | ||
| + | # other associated software easier. | ||
| + | |||
| + | # | ||
| + | # The format of this file is: | ||
| + | #portname callsign speed paclen window description | ||
| + | udr0 N7NIX-10 9600 255 2 Winlink | ||
| + | </file> | ||
| + | === ax25d.conf === | ||
| + | <file> | ||
| + | # /usr/local/etc/ax25/ax25d.conf | ||
| + | # | ||
| + | # ax25d Configuration File. | ||
| + | # | ||
| + | # | ||
| + | [N7NIX-10 VIA udr0] | ||
| + | NOCALL * * * * * * L | ||
| + | NOCALL * * * * * * L | ||
| + | default * * * * * * - rmsgw /usr/local/bin/rmsgw rmsgw -l debug -P %d %U | ||
| + | # | ||
| + | [N7NIX VIA udr0] | ||
| + | NOCALL * * * * * * L | ||
| + | default * * * * * * 0 gunn /usr/local/bin/wl2kax25d wl2kax25d -c %U -a %d | ||
| + | # | ||
| </file> | </file> | ||
