Install paclink-unix
- Configure a single MTA
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
plu:install_exim [2016/04/14 08:28] gunn |
plu:install_exim [2016/04/14 08:36] (current) gunn |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Installation Instructions For Exim ====== | + | ====== Installation Instructions For Exim4 ====== |
- | ===== Installation Instructions by Charles, AI4RI ===== | + | |
- | * [[plu:install_exim:ai4ri | Install exim-heavy for paclink-unix]] | + | |
===== Installation Instructions by Apostolos, SV1LJJ ===== | ===== Installation Instructions by Apostolos, SV1LJJ ===== | ||
- | * [[plu:install_exim:sv1ljj | Install exim for paclink-unix]] | + | * [[plu:install_exim:sv1ljj | Install exim4-light for paclink-unix]] |
- | ===== Installation Instructions for exim4 wl2k system filter ===== | + | ===== Installation Instructions by Charles, AI4RI ===== |
- | + | * [[plu:install_exim:ai4ri | Install exim4-heavy for paclink-unix]] | |
- | * place the file [[#systemfilter_exim_mta_wl2k_filter_-_exim_s_version_of_wl2km4 | system.filter]] (see below) into the ///etc/exim4// directory. | + | |
- | * cut and paste the following into the top of the ///etc/exim4/exim4.conf.template// file: | + | |
- | + | ||
- | <file> | + | |
- | ########################################################################### | + | |
- | ## WINLINK 2000 Filter | + | |
- | ########################################################################### | + | |
- | system_filter = "/etc/exim4/system.filter" | + | |
- | system_filter_user = Debian-exim # Set this to the user that exim runs as | + | |
- | system_filter_group = Debian-exim # Set this to the group that exim runs as | + | |
- | system_filter_pipe_transport = address_pipe | + | |
- | system_filter_file_transport = address_file | + | |
- | system_filter_reply_transport = address_reply | + | |
- | system_filter_directory_transport = address_directory | + | |
- | </file> | + | |
- | + | ||
- | * this must go at the top of the file underneath the following lines: | + | |
- | <file> | + | |
- | # Macro defining the main configuration directory. | + | |
- | # We do not use absolute paths. | + | |
- | .ifndef CONFDIR | + | |
- | CONFDIR = /etc/exim4 | + | |
- | .endif | + | |
- | </file> | + | |
- | * make sure that the wl2k directories for paclink-unix are set for the debian username/group that exim is using. | + | |
- | * By default this is Debian-exim.Debian-exim, this MUST be the same as system_filter_user and system_filter_group. | + | |
- | + | ||
- | <code bash> | + | |
- | chown -Rv Debian-exim.Debian-exim /usr/local/var/wl2k | + | |
- | </code> | + | |
- | + | ||
- | * restart exim: | + | |
- | <code bash> | + | |
- | /etc/init.d/exim4 restart | + | |
- | </code> | + | |
- | + | ||
- | * create a blank eximfilter.log file in the wl2k folder: | + | |
- | <code bash> | + | |
- | touch /usr/local/var/wl2k/eximfilter.log && chown Debian-exim.Debian-exim /usr/local/var/wl2k/eximfilter.log && \ | + | |
- | chmod 666 /usr/local/var/wl2k/eximfilter.log | + | |
- | </code> | + | |
- | * all message processing by the filter will be logged into ///usr/local/var/wl2k/eximfilter.log// | + | |
- | ===== system.filter, EXIM MTA wl2k filter - exim's version of wl2k.m4 ===== | + | |
- | + | ||
- | <file> | + | |
- | # Exim filter <<== do not edit or remove this line! | + | |
- | + | ||
- | # EXIM4 filter for paclink-unix WL2K software | + | |
- | # | + | |
- | # Created by Charles Blackburn "AI4RI" | + | |
- | # | + | |
- | # ai4ri@winlink.org - charlesb@cflpacket.net | + | |
- | # | + | |
- | # | + | |
- | + | ||
- | ##----------------------------------------------------------------------- | + | |
- | # only run any of this stuff on the first pass through the filter - this | + | |
- | # is an optimisation for messages that get queued and have several delivery | + | |
- | # attempts | + | |
- | + | ||
- | if not first_delivery then | + | |
- | finish | + | |
- | endif | + | |
- | ##----------------------------------------------------------------------- | + | |
- | + | ||
- | ##----------------------------------------------------------------------- | + | |
- | # if this is an error notification message, make sure it doesn't get lost | + | |
- | if error_message then | + | |
- | finish | + | |
- | endif | + | |
- | ##----------------------------------------------------------------------- | + | |
- | + | ||
- | # Create a logfile of message IDs processed" | + | |
- | logfile /usr/local/var/wl2k/eximfilter.log | + | |
- | logwrite "-----------------------------------------------------------------------" | + | |
- | logwrite "$tod_log SYSTEM.FILTER: Processing Message: $message_id" | + | |
- | logwrite "From: $header_from ($sender_address) -> To: $header_to" | + | |
- | logwrite "Subject: $h_subject" | + | |
- | logwrite "Message size: $message_size bytes" | + | |
- | + | ||
- | # Check if this is a message going to a winlink account *@winlink.org | + | |
- | if | + | |
- | $header_to: contains "@winlink.org" and # if it's going to a winlink account | + | |
- | $sender_address: does not contain "root@" # AND it's NOT coming via paclink (will always have a sender of root@) | + | |
- | then # it must be an outgoing wl2k message, so put into wl2k/outbox | + | |
- | logwrite "$message_id is an OUTGOING WL2K Message" | + | |
- | logwrite "Sending to pipe" | + | |
- | unseen pipe "/usr/local/libexec/mail.wl2k" | + | |
- | # unseen save /usr/local/var/wl2k/outbox/ | + | |
- | logwrite "We're done here this time...." | + | |
- | seen finish | + | |
- | endif | + | |
- | + | ||
- | # Check if this is a message coming from a winlink account *@winlink.org or via paclink | + | |
- | if | + | |
- | $header_to: contains "@winlink.org" and # it's coming FROM a winlink account (mail -r call@winlink.org) | + | |
- | $sender_address: contains "root@" # AND it's coming via paclink (will always have a sender of root@) | + | |
- | then # it must be an incoming wl2k message via paclink | + | |
- | logwrite "$message_id is an INCOMING WL2K Message via paclink" | + | |
- | unseen finish | + | |
- | endif | + | |
- | # if it's FROM a winlink address (mail -r call@winlink.org) then send via pipe | ||
- | if | ||
- | $header_from: contains "@winlink.org" | ||
- | then | ||
- | logwrite "$message_id is a message going OUT from a winlink address" | ||
- | logwrite "Sending to pipe" | ||
- | unseen pipe "/usr/local/libexec/mail.wl2k" | ||
- | # unseen save /usr/local/var/wl2k/outbox/ | ||
- | seen finish | ||
- | endif | ||
- | # end of filter - make sure that this message gets processed if it if it bombs out to here, it failed the above filters | ||
- | logwrite "$message_id is not a WL2K Message" | ||
- | unseen finish | ||
- | </file> |